How to Print Multi-Part Carbonless Forms in a Laser Printer

Need to convert continuous carbonless forms to a laser format? Carbonless laser paper is an ideal solution. Find common carbonless paper applications here.

multipart carbonless formsMulti-part carbonless paper in a laser printer? No way!

Yes way! There is a whole new breed of carbonless papers created specifically for use in laser printers. These NCR (“No Carbon Required”) papers are not only laser-compatible, but clean and green.

So how does this work? If you need a three-part form, what do you do?

Selecting the correct collation type for your printer

Before you can print, you need to make sure that you buy the right type of forms. The way the carbonless laser paper will travel through your printer – how your printer pulls the paper and then outputs it – will determine which you need.

Why? Because there are special coatings on the paper that allow the transfer of writing through the layers, but the transfer can only work when the paper is in the correct sequence. Some printers will flip paper during the printing process and some will not, so testing your printer’s output and input will determine the type of paper you should buy and how to load it into your printer.

Do you need straight or reverse collated carbonless paper?

To know which type of collation you need, you must determine how your printer inputs & outputs paper. We recommend the following test:

  1. Draw a hand-written X on a sheet of paper.
  2. Place that sheet into the printer tray you plan to use for your carbonless forms and make a note of which way you put it in. Did you put it in with the X face up or face down? Make a note: “I put the paper in face ___, so that’s the input.”
  3. Print a single, one-sided page from a Word doc with the word “test” on it. Make sure you use the same printer tray as your X doc.
  4. Observe how the printed sheet comes out of the printer and sits on the output tray. Make a note: “The paper was face ____ on the output tray, so that’s the output.”
  5. Note: the hand-written X and the printed word “test” must be on the same side of the paper for this test to work properly. If they come out on opposite sides, start over and on step #2 place your sheet in the tray the opposite way you did the first time. Record your results again.
  6. Take your notes and follow through the table below to determine if you need straight or reverse collated multi-part forms.

Determine straight vs. reverse collated multi-part carbonless forms

  1. Once you know what you need, purchase the correct forms.

How to print a three-part form

Once you receive the correct paper, you are ready to print! Consult your note from step #2 in the test above. What was the input method that worked (you got the X and “test” on the same side) – putting the paper in the tray face up or face down?

How to load the paper into the tray

Remember: make sure you are using the same tray you used for the above tests.

  • If your printer input test gave you a “face up” result, hold your paper ream so that the arrow on the label faces up. Keep the ream in that position – don’t flip it. Rip open the package, lift the paper and place it into the tray. Remember, don’t ever flip that ream over!
  • If you got a “face down” result on the input test, you will want the arrow on the label to face down (so the label will actually be upside down). Keep the ream in that position – don’t flip it. Rip open the package, lift the paper and place it into the tray. Again, don’t flip that ream!

Carbonless multi-part forms labels

If you have followed these steps, you should be able to just print regularly without adjusting any printer settings. For a three-part form, you’ll print three identical copies. For example, if you needed five sets of your three-part forms, you would simply set the printer to print 15 copies. The paper will come out of the printer in the correct order.

Finished product

Straight Collated Forms

If you’re using three-part straight collated forms, when they are output, the pink will be on top, face down. As you lift them off the tray and turn them over, they are in the correct order, ready for use.

Reverse Collated Forms

If you’re using three-part reverse collated forms, output will be the white sheet on top, face up. The pre-collated forms will be in the correct order to use.

Reminder: never change the order of carbonless forms. For the special coatings to work and writing to transfer from sheet to sheet, the paper must stay in the correct order.

Coatings multi-part carbonless forms

How to keep multi-part carbonless forms in sets

The easiest way is to separate multi-part carbonless forms is by color, so always make sure the correct color sheet is at the bottom of the stack.

Unlike the forms created for impact printers, these sets are not joined in any way. So what do you need to do to put them together? There are several ways:

  • Staple the sets together
  • Put them on a clipboard
  • Glue them
  • Or use them as separate sheets

The choice is yours. You need to determine which works best for your application. By discussing your needs with a specialist in this product, you may find that the 3-part sets you were using can now be condensed into 2-part sets.

Carbonless laser paper form options

Do you have various different uses for carbonless laser paper? Perhaps you need some 2-part and some 3 or 4-part sets, then you may be best served by using 1-part coated front & back carbonless forms so that you can tailor the number of sheets to the application.

Do you have a 3-part shipping form, a 2-part statement or even a 4-part purchase order or delivery form? Using a 1-part coated front & back carbonless form will allow you to choose the number of sheets as you print.

Benefits of Carbonless Laser Forms

Whatever your need, you can cut costs by the versatility carbonless laser forms offer. They will run on every machine, including laser, offset press, high-speed copiers and digital duplicators.

And a huge benefit over pre-printed forms is that if you change an address, a phone number or conditions, you don’t have to toss the unused portion of your forms. You simply print what is called for with the most pertinent information and you will always have updated information; no reprinting necessary.

For a deeper dive into Carbonless Laser Forms, check out some FAQs. To try multi-part carbonless laser forms for yourself, request samples below. Ready to buy right now? You can visit our online store.

Reimage Sample Request

*This post was originally published in February 2015. It was updated in December 2016, June 2019 and March 2020.

Medical Forms Are a Nightmare. Carbonless Paper Can Help!

See how Relyco’s REIMAGE carbonless paper helped one hospital increase efficiency and reduce cost.

Carbonless laser paper

At Relyco, we have this friend. Her name is Hypothetical Holly.

Hypothetical Holly works in a hospital, keeping and organizing medical records and forms. It’s difficult work, and before the advent of carbonless paper, it was incredibly messy work. Holly spent her days covered in black smudges from forms that needed to be completed in triplicate, buried in discarded carbon sheets.

Carbonless paper saved Holly from that sooty fate, but it too has its challenges. Traditional carbonless paper is not intended for use in a laser-compatible environment, and has severely damaged parts of the hospital’s laser printers and digital copiers.

Luckily for Holly, there is a solution, as Griffin Hospital in Derby, Conn. discovered a few years ago: It’s called REIMAGE™ Carbonless Laser Paper.

Customer Story: Griffin Hospital’s Carbonless Paper Solution

Griffin Hospital is a 160-bed acute care community hospital serving more than 100,000 residents of the Lower Naugatuck Valley Region and also serves as the flagship hospital for Planetree, an international leader in patient-centered care.

The hospital operates its own print shop, which delivers a comprehensive range of printing services on demand to departments across the health care organization. Long-time employee Steven C. Katilius, the print shop’s sole operator, said that the facility uses carbonless laser paper for a range of documents, from discharge instructions to payment receipts. 

Katilius tried a sample of REIMAGE on the print shop’s Risograph, a high-speed digital duplicator, and was so impressed with the results that it’s all he’s used since.

Some carbonless papers cause issues with the equipment, but the REIMAGE works flawlessly; it has literally never jammed, which saves me time in the long run. The adhesive Relyco recommends for use with REIMAGE dries quickly and works great to produce multi-page form sets. Most importantly, though, when the carbonless forms are used throughout the hospital, the writing is clear, even on the third sheet, which is a critically important quality in the types of forms we produce.

It’s also cost-effective, Katilius said. Carbonless paper can be expensive, but Relyco’s prices for REIMAGE are very competitive, he said.

Interested in learning more about Relyco’s REIMAGE Carbonless Laser Paper and its applications to the healthcare industry? Request free samples below.

Reimage Sample Request

Ammunition Manufacturer Saves Time and Money Printing Carbonless Forms – A Customer Story

Here’s how a government-contracted ammunition manufacturer reduced costs, saved time, and streamlined processes by printing carbonless forms in-house.

Carbonless Forms Case Study MainAmerican Ordnance, a subsidiary of Day & Zimmerman, manufactures ammunition for the U.S. military at locations in Tennessee and Iowa. As it ships ammunition to U.S. military installations, it is critical to be able to monitor each shipment in transit.

Specialized forms need to accompany each shipment, but their traditional carbon paper forms were becoming cumbersome and costly. Here’s how our carbonless forms helped streamline operations and save the company money.

The Customer Challenge

The company produces four copies of the form for each shipment, including the packing slip and bill of lading which details the enclosed merchandize and gives title of that shipment to a specified party. One copy stays at the plant, and the others need to be signed as the shipment reaches each installation. As shipping manager Brad Vance explains, specialized forms accompany each shipment.

“We average 50 shipments each week and produce four copies of each shipping form–including the packing slip and bill of lading–one that stays at the three that must be signed as the shipment reaches each installation,” Vance says. “Until four years ago, the four copies of each form were created using carbon paper–an average of 240 sheets per week. Creating the forms and using them in transit was an expensive and messy process.”

The RELYCO Solution

American Ordnance needed a way to reduce costs and streamline it processes. Our cost-effective carbonless forms solution led American Ordnance to RELYCO. Since instituting the use of REIMAGE carbonless laser paper, American Ordnance not only has seen the benefits of using a carbonless solution, but has realized significant savings in costs and time.

The ease of use of the product has been a key factor in assuring a smooth flow of shipping documents from the manufacturing facility to its final destination. Read the full case study here.

Benefits of Printing Carbonless Forms In-House

Carbonless laser forms are a cost effective and versatile solution. They will run on every machine, including laser, offset press, high-speed copiers and digital duplicators.

And a huge benefit over pre-printed forms is that if you change an address, a phone number or conditions, you don’t have to toss the unused portion of your forms. You simply print your own carbonless forms with the most pertinent information and you will always have updated information; no reprinting necessary.

For more information on carbonless forms call us at 800.777.7359 or request free samples below.

Reimage Sample Request

Four Laser Substrates to Increase Your In-Plant’s Value

Investing in a few new laser substrates can help in-plant printing departments prove their value and justify the cost of maintaining an in-plant solution.

Laser Substrates to Increase In-Plant Value

As more and more businesses and governmental bodies turn to outsourcing their print work, in-plant printing departments must prove their value to justify the cost of maintaining an in-plant solution.

New Laser Substrates to Grow In-House Capabilities

One of the best ways to enhance the value of your in-plant printing program is to increase the number of unique applications you are able to handle in-house.

Investing in a few new substrates like waterproof paper, carbonless paper, custom packaging solutions and pressure seal forms and equipment can help your in-plant printing department grow its capabilities exponentially.

Colorful Waterproof Paper

Synthetic paper has dozens of applications for any industry where durability and water-resistance are important.

But you can take your waterproof paper applications to the next level with the newest technology: synthetic waterproof paper in vibrant colors. With brightly colored synthetic paper, there’s no need to lay a full-color bleed on your waterproof applications.

Some of the most common applications for synthetic paper include:

  • Durable signage
  • ID & membership cards
  • Parking passes
  • Temporary license plates
  • Bookmarks
  • Labels
  • Menus
  • Field manuals

REVLAR Premium Colors provides the perfect canvas for bright and light colored applications like signs, tags, banners, posters or flyers without the use of excessive ink and toner. Plus, you can even incorporate white toner!

Custom Packaging Solutions

Sometimes all it takes to reinvigorate your brand is an enhanced packaging solution. Think about personalized packaging for direct mail, presentations, corporate gifts, special events and fundraising.

A few common applications for custom packaging solutions include:

  • Table tents
  • Candy boxes
  • Card boxes
  • Bottle labels
  • Coffee cup sleeves

Carbonless Paper

If you’re still using old-school pin-fed forms and printers, you can increase the quality and efficiency of your form production with a carbonless paper solution like REIMAGE carbonless laser paper.

Here are just a few of the most common applications for carbonless paper:

  • Printing registration forms
  • Invoices
  • On-demand work orders
  • Medical forms
  • Sales receipts
  • Employment applications

Pressure Seal Forms & Equipment

Pressure seal forms and equipment let businesses create and process self-sealing one-piece self-mailers. Investing in a pressure seal forms and equipment solution, like RELYCO’s ULTRASEAL line, can not only enhance your in-house capabilities, it can also help your business save money while potentially generating better open-rates.

The benefits of using pressure seal forms and equipment include: reduced overhead by eliminating envelope costs, reduced man-hours spent by hand-stuffing envelopes and increased response rates!

Common applications for pressure seal include:

  • Efficient mass-mailing
  • Delivery of secure information like tax forms, checks & grade reports
  • Promotional self-mailers

Want to learn more about how laser substrates like waterproof paper can help grow your in-house capabilities? Click below to download our white paper for all the details.


Carbonless Paper FAQs: Everything You Need to Know

Do the forms run through the printer at the same time? How do the forms stay together? Does laser carbonless paper come pre-collated and un-collated? Find these answers and more.

REIMAGE Carbonless Laser Paper is an environmentally-friendly, cost-effective, laser printer compatible carbonless paper solution. It is ideal for converting continuous carbonless forms to a laser format.

Frequently Asked Questions about Carbonless Laser Paper

Here are some of the most frequently asked questions about carbonless laser paper.

Carbonless paperQ. Can I use traditional carbonless paper in my laser printer?

A. Traditional carbonless paper—the kind typically used in continuous, multi-part forms—is not intended for use in a laser printer. Although traditional carbonless paper will run through most printers, it is manufactured with solvent-based chemicals that can cause severe damage to rollers, drums and other critical printer components.

REIMAGE Carbonless Laser Paper is manufactured specifically for safe use in laser printers and digital copiers and will not damage printing equipment.

Q. Do the forms run through the printer at the same time? How do the forms stay together? How does the laser printer print multiple copies of the same form?

A. Traditional carbonless multi-part forms are made up of multiple sheets that are usually pin fed through an impact printer via removable line holes on either side. These types of forms are printed on the top page, and that printing is imaged on the remaining parts using carbonless technology. All the printing and imaging is done simultaneously (one pass through the printer).

Since a laser printer can only print a single sheet at a time, with carbonless laser forms, a user prints multiple copies of the same form. For example, with a three-part form, you simply print three copies of each form, one after the other, on the carbonless laser paper. The paper for multi-part forms can be purchased pre-collated; with a three-part form, the top sheet is white, the middle sheet is canary and the bottom sheet is pink. So if you needed four sets of three-part forms, for example, you can just set the printer to print 12 copies. The paper will come out of the printer in the correct order.

Once they’ve been printed, the forms may be stapled, bound or glued into sets, or left as is, without any binding.

Q. Does laser carbonless paper come pre-collated and un-collated?

A. REIMAGE Carbonless Laser Paper is available pre-collated for single tray use or uncollated for use in multiple-tray (or even multiple-printer) applications. Pre-collated carbonless laser paper is available in straight and reverse sequences for three-part and four-part forms. Why? Because different laser printer models load, feed and output differently, so you want to make sure you use the collation type that is compatible with your printer. To determine whether you need straight or reverse collated paper, follow the instructions to test printer output in this blog post or in this printable document.

Once you have completed the test to determine what your printer output is, you can use this chart to know the collation you need:

Paper inputPrinter outputWhat form you will need
Face upFace upReverse collated forms
Face upFace downStraight collated forms
Face downFace downReverse collated forms
Face downFace upStraight collated forms

Q. Why does reverse vs. straight collation matter? How do the forms flow through the printer?

A. Understanding your printer’s output is extremely important for carbonless forms. Why? Carbonless forms have special coatings on certain sides that allow the transfer of writing through the paper sets. If the paper gets flipped during printing, then the correct coatings may no longer line up for the finished product, which would render the paper useless.

Straight Collated for REIMAGE Carbonless Forms

In straight collated forms, the printer pulls the stock in the tray from the top of the stack. Then it outputs it face down. As you lift them off the tray and turn them over, they are in the correct order, ready for use.

Reverse Collated for REIMAGE Carbonless Forms

Again, in reverse collated forms, the printer will pull the paper from the top of the stack, but it will start with sheet 3. So you load your input tray with sheet 3 (the pink form) at the top, face up. Output will be white sheet on top, face up. The forms will be in the correct order to use. Be sure not to change that order.

Is this explanation confusing to you? Don’t worry! We included it for the visual learners, but it can be too much for others. Simply follow the printer output test steps outlined here and order reverse or straight forms based on your results.

Q. Why don’t I need to worry about straight vs. reverse sequencing for two-part forms?

A. You can purchase our two-part carbonless laser paper pre-collated, but you don’t need to choose between reverse or straight collation (like you do with three or four-part forms). Why? Because when dealing with only two sheets of paper, they can’t get out of order. But it is still important to do your printer input test (in the next question) to make sure you put the paper in the tray properly.

Q. Do I put the paper face up or face down in my printer tray?

A. To determine whether you should put your carbonless laser paper in the tray face up or face down, follow the instructions to test your printer input in this blog post or this printable document.

Q. Is testing laser carbonless paper recommended?

A. Yes! Because each application is unique, physical testing of REIMAGE Carbonless Laser Paper using the actual laser printer and laser printer trays on which the forms will be printed is the most effective way to determine which REIMAGE option is right for you. Please make sure to do the testing recommended in this blog post and request free samples if you need them! When printing multi-part forms, we always recommend that you print one set – and test that the transfer of writing works – prior to each print run.

Reimage Sample Request

This post was originally published in March 2015. It has been updated in June 2019.

How Does Carbonless Paper Work?

Carbonless paper produces an image on multipart forms without the use of messy and unsecure carbon forms. But how does this magic work? Get all the details.

How Does Carbonless Paper Work?

Carbonless laser paper is an environmentally-friendly, cost-effective, laser-compatible carbonless paper solution ideal for converting continuous carbonless forms to a laser format.

Before carbonless paper was invented, multipart forms were made up of sheets of regular paper separated by sheets of thin, tissue-like carbon paper—often referred to as “carbon interleaved.”

A user would write (or impact print) on the front of the form, and the pressure from the writing or printing would cause the carbon from each sheet of carbon paper to image on the piece of paper beneath it.

Disadvantages of Carbon Forms

Though very common, carbon forms had a number of disadvantages. First, they could be extremely messy, often leaving users with black carbon on their fingers and anything else they touched.

Second, once the forms had been completed and the carbon sheets were removed and discarded, the information that had been printed on the forms could be read on the discarded carbon paper, making security an issue with certain types of forms.

IN 1954, CARBONLESS PAPER WAS INVENTED.

What is Carbonless Paper?

Carbonless paper is coated with two different types of chemicals: CF or Coated Front, and CB or Coated Back. These chemicals are held in tiny capsules and are released when the capsules are burst by pressure from a pen or printer.

When the CF and CB chemicals interact, the CF chemicals darken causing an image to appear on the CF side of the sheet. One easy way to tell that the CF and CB chemicals are different is that the image appears on only the front sheet; there is no image on the back of any sheets.

Since this type of paper produces an image without carbon, it is called “carbonless paper.”

The Difference Between Traditional Carbonless Paper and Carbonless Laser Paper

The most important difference between traditional carbonless paper and carbonless laser paper is that traditional carbonless paper is manufactured with solvent-based chemicals that can damage critical printer components, including rollers, drums and other printer components.

Carbonless laser paper is designed specifically for use in laser printers and digital copiers. Since its imaging capsules are not solvent based, they cause no damage to the components of the printer.

To Learn More

To learn more about how REIMAGE carbonless paper works, call 1-800-777-7359 or email info@relyco.com.

Reimage Sample Request

Three Printing Business Ideas to Attract and Retain New Customers

As more and more customers move their printing in-house, these three printing business ideas can help print shops can retain old and attract new customers.

Three Printing Business Ideas

As a print shop owner, you know that your competition is more than just another print shop. Customers are doing a lot of their own printing in-house, making the customer a competitor. So how do you stay afloat and retain current customers while attracting new printing business?

Printing Business Ideas You Can Try Today

Put these three easy printing business ideas into practice to win new customers without huge equipment investments.

Specialize in Short-Run Printing

Many print shops find themselves getting a lot of requests for smaller jobs, but losing them on price. One way around that is to reduce your overhead by locating a supplier that offers a variety of paper types in small quantities.

Now when someone wants 100 save-the-date invitations, you can use the less costly digital equipment that you already have on hand and win the job.

Offer a Unique Paper Type

With all the competition out there, you want your printing business to stand out. What better way than to offer a unique specialty paper?

Everyone wants their message to be the one that gets all the attention. Be the print shop that offers personalized messages on a specialty paper that gets people talking. A few of the most versatile and popular paper substrates include:

Help your Customers Grow Their Business with Direct Mail

You want your business top-of-mind when your customers need printed media. One way your print shop can accomplish that is by offering to do direct mail for your customers.

Target their customers with a personalized piece to help your clients win more business, and encourage them to refer those clients to you for an extra value-add!

Increase Your Printing, Not Your Overhead!

To grow your business, you have to be economical and innovative. Rather than shelling out for a new suite of printing equipment, you can increase both your capabilities and offerings by following the tips listed above.

Combining unique and eye-catching media, personalized printed materials, and unique substrates offered in small quantities are some of the ways you can retain your existing customers AND attract new clients without a huge investment in new printing equipment.

New Call-to-action

Benefits of Carbonless Laser Paper

In addition to being a cost-effective and waste-reducing solution, Relyco’s carbonless laser paper is also safe for laser printers and digital copiers, unlike traditional solvent-based carbonless paper.

Benefits of carbonless paper

Unlike traditional carbonless paper, carbonless laser paper is designed specifically for use in laser printers and digital copiers. How? The imaging capsules that coat one side of carbonless laser paper are not solvent-based, so they cause no damage to the internal components of the printer, unlike traditional solvent-based carbonless paper.

Carbonless laser paper can be very cost effective. On average, more than 30 percent of preprinted traditional carbonless forms are discarded within six to 12 months due to obsolescence or a change in the form or business process. Carbonless laser paper solutions eliminate waste because the forms can be customized and printed if and when they’re needed.

Other advantages of Carbonless Laser Paper include:

  • Speed — Allows user to create multi-part forms instantly.
  • Accuracy — Eliminates transcription errors.
  • Security — Prevents alteration; any change to a copy is instantly evident.
  • Clarity — Provides a sharp copy image.
  • Clean — Prevents text image from smearing or rubbing off.
  • Versatile — Enables reverse printing or color coding to suit business needs.
  • Cost-effective — Allows user to print only what is needed and avoid costly changes.

To learn more about REIMAGE carbonless laser paper, call us at 1-800-777-7359 or Email us.

Reimage Sample Request

*This post was originally published in July 2011. It has been updated in May 2019.

When a Cold Winter’s Day Impacts Your Laser Printer

Static electricity is a common problem on cold winter days when the humidity is low. Check out these tips to fight static and keep your laser printer running in tip-top shape!

When temperatures drop and the air is dry, you get static electricity, which is the nemesis of technology and equipment. While it may be fun to shuffle across the carpet and shock your friend on the ear, this same static electric shock can wreak havoc on your laser printers and digital copiers – affecting printer runnability and print quality.

How do you know if there is a problem?

Static electricity is a common problem on cold winter days when the humidity is low. If your laser printer is producing streaky outputs, you may have a static issue. In order to make the toner stick to the paper, laser printers charge the paper with particles. If the paper has too much static electricity, the particle transfer can be disrupted, which can result in streaking and even paper jamming.

Consider these options to ensure optimal performance:

  1. To prevent problems (paper delivery, sheet alignment, toner adhesion) relating to static electricity, the most important factor is relative humidity. Keep the relative humidity of the printing environment above 50 percent humidity. To do this, install a humidifier or talk to your HVAC technician.
  2. To help clear your paper of static electricity, you can hold a stack of paper firmly in one hand and fan it out a few times with the thumb and index finger of your other hand.  Do this a few times and then immediately place the stack of paper into the printer. If it’s a large commercial printer or you’re doing a big job, you can also use a paper jogger to automate this process.Skip ahead to the 2-minute mark in the video below to see what correct paper fanning looks like:


  1. When new shipments of products (pressure seal forms, carbonless laser paper, synthetic papers) arrive for use in your laser printer or copier, allow the product to acclimate to your print room environment. This will also help alleviate any additional static conditions.
  2. Where and how you store your paper also matters. You should store your paper products in an area with moderate humidity for best results. This will help keep the paper static free.
  3. Make sure your equipment is grounded. This helps your equipment to better handle a static charge and overcome related issues.

If you need more advice and info on how Relyco can help, call us at 800-777-7359 or contact us.

*This blog post was originally published in March 2011 and it was updated on May 29, 2019.